Indesit K6T52S(X)/AUS Instruções de Utilização descarregar pdf (Página 9)

AUS

Start-up and use

Using the hob

Lighting the burners

For each BURNER knob there is a full ring showing

the strength of the flame for the relevant burner.

To light one of the burners on the hob:

1. Bring a flame or gas lighter close to the burner.

2. Press the BURNER knob and turn it in an

anticlockwise direction so that it is pointing to the

maximum flame setting E.

3. Adjust the intensity of the flame to the desired

level by turning the BURNER knob in an

anticlockwise direction. This may be the minimum

setting C, the maximum setting E or any position in

between the two.

If the appliance is fitted with an electronic lighting

device* (

see figure

), press and then hold the

BURNER knob down and turn it in an anticlockwise

direction, towards the maximum flame setting, until

the burner is lit.The burner may be extinguished

when the knob is released. If this occurs, repeat the

operation, holding the knob down for a longer period

of time.

! If the flame is accidentally extinguished, switch off

the burner and wait for at least 1 minute before

attempting to relight it.

If the appliance is equipped

with a flame failure safety

device*, press and hold the

BURNER knob for

approximately 2-7 seconds

to keep the flame alight and

to activate the device.

Check that the gas has been lit. If the burner fails to

ignite try again. If the burner fails to ignite after 3

attempts, wait a few minutes for the gas to disperse

before making any further attempts.

If the burner still fails to ignite, a match or lighting

device can be used, but care must be taken. If the

problem persists, contact place of purchase or their

appointed agent for service.

If the flame has excessive yellowing, or appears to

lift off the burner ports, or makes a loud noise, turn

the burner off and call your service agent.

To switch the burner off, turn the knob until it

reaches the stop position •.

Lighting the burners for the first time

If the appliance is being used for the first time, or if

it has not been used for a long period of time, it may

be necessary to purge the gas lines of excess air

before you can successfully light the burners.

To do this, turn each burner to High for 10-15

seconds and press the ignition button several times.

If the burner does not light, repeat this procedure

twice more. Wait 1-2 minutes for any gas build up to

disperse before allowing any further gas flow.

Practical advice on using the burners

For the burners to work in the most efficient way

possible and to save on the amount of gas

consumed, it is recommended that only pans that

have a lid and a flat base are used. They should

also be suited to the size of the burner.

Do not use pans which are unstable or which have a

warped or damaged base.

Ensure the pot sits securely on the trivet and is

centred above the burner.

Burner ø Cookware Diameter (cm)

Fast (R) 24 - 26

Semi Fast (S) 16 - 20

Auxiliary (A) 10 - 14

Triple Crown (TC) 24 - 26

To identify the type of burner, please refer to the

diagrams contained in the “Technical

Specifications”.

Using the oven

! The first time you use your appliance, heat the

empty oven with its door closed at its maximum

temperature for at least half an hour. Ensure that the

room is well ventilated before switching the oven off

and opening the oven door. The appliance may emit

a slightly unpleasant odour caused by protective

substances used during the manufacturing process

burning away.

! Before operating the product, remove all plastic

film from the sides of the appliance.

! Never put objects directly on the bottom of the

oven; this will avoid the enamel coating being

damaged.

HOB GAS BURNER

SAFETY DEVICE

ELECTRONIC

LIGHTING DEVICE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 19 20

Comentários a estes Manuais

Sem comentários

Indesit K6T52S(X)/AUS Instruções de Utilização Página 9

Comentários a estes Manuais

Manuais e produtos relacionados com Fogões Indesit K6T52S(X)/AUS